En alternative à Etcher qui envoie des données à Google et autres lors de son utilisation.
Installing operating system images on Linux
Etcher is typically the easiest option for most users to write images to SD cards, so it is a good place to start. If you're looking for more advanced options on Linux, you can use the standard command line tools below.
Note: use of the
dd tool can overwrite any partition of your machine. If you specify the wrong device in the instructions below, you could delete your primary Linux partition. Please be careful.
Discovering the SD card mountpoint and unmounting it
lsblk to see which devices are currently connected to your machine.
If your computer has a slot for SD cards, insert the card. If not, insert the card into an SD card reader, then connect the reader to your computer.
lsblk again. The new device that has appeared is your SD card (you can also usually tell from the listed device size). The naming of the device will follow the format described in the next paragraph.
The left column of the results from the
lsblk command gives the device name of your SD card and the names of any paritions on it (usually only one, but there may be several if the card was previously used). It will be listed as something like
/dev/sdX (with partition names
/dev/sdX1 respectively), where
X is a lower-case letter indicating the device (eg.
/dev/sdb1). The right column shows where the partitions have been mounted (if they haven't been, it will be blank).
- If any partitions on the SD card have been mounted, unmount them all with
umount, for example
umount /dev/sdX1 (replace
sdX1 with your SD card's device name, and change the number for any other partitions).
Copying the image to the SD card
Copying a zipped image to the SD card
In Linux it is possible to combine the unzip and SD copying process into one command, which avoids any issues that might occur when the unzipped image is larger than 4GB. This can happen on certain filesystems that do not support files larger than 4GB (e.g. FAT), although it should be noted that most Linux installations do not use FAT and therefore do not have this limitation.
The following command unzips the zip file (replace 2018-11-13-raspbian-stretch.zip with the appropriate zip filename), and pipes the output directly to the dd command. This in turn copies it to the SD card, as described in the previous section.
ATTENTION NE PAS OUBLIER L'OPTION
-p POUR TRANSFÉRER LES FICHIERS, SANS LES CONVERTIR, AU PIPE (stdout)
unzip -p 2018-11-13-raspbian-stretch.zip | sudo dd of=/dev/sdX bs=4M conv=fsync
Checking the image copy progress
Optional: checking whether the image was correctly written to the SD card
dd has finished copying, you can check what has been written to the SD card by
dd-ing from the card back to another image on your hard disk, truncating the new image to the same size as the original, and then running
md5sum) on those two images.
If the SD card is much larger than the image, you don't want to read back the whole SD card, since it will be mostly empty. So you need to check the number of blocks that were written to the card by the
dd command. At the end of its run,
dd will have displayed the number of blocks written as follow:
xxx+0 records in
yyy+0 records out
yyyyyyyyyy bytes (yyy kB, yyy KiB) copied, 0.00144744 s, 283 MB/s
We need the number
xxx, which is the block count. We can ignore the
- Copy the SD card content to an image on your hard drive using
dd bs=4M if=/dev/sdX of=from-sd-card.img count=xxx
if is the input file (i.e. the SD card device),
of is the output file to which the SD card content is to be copied (called
from-sd-card.img in this example), and
xxx is the number of blocks written by the original
- In case the SD card image is still larger than the original image, truncate the new image to the size of the original image using the following command (replace the input file
reference argument with the original image name):
truncate --reference 2018-11-13-raspbian-stretch.img from-sd-card.img
- Compare the two images:
diff should report that the files are identical.
diff -s from-sd-card.img 2018-11-13-raspbian-stretch.img
sync. This will ensure that the write cache is flushed and that it is safe to unmount your SD card.
- Remove the SD card from the card reader.